Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
忘记了密码? how can I recover my password now!
Enter right registered email to receive password!
Estimate the percent scrap in producing round blanks if the clearance between blanks is one tenth of the radius of the blank. Consider single and multiple-row blanking, as sketched in Fig. P16.55.
In a certain binomial distribution, π = 0.20 and n = 30, In using the normal approximation,- What are the mean and standard deviation of the corresponding normal distribution?
The benefits and challenges of Agile Project Management:Present a tentative title for your topic.Briefly describe how the topic relates to project management.State a concrete, specific research question to guide your review of the literature.
Create policy statements that align with HIPAA regulations that address patient health care record handling and disposal. Describe relevant training topics for staff in order to educate them on the handling and disposal of patient records.
In a certain binomial distribution, π = 0.25 and n = 40, In using the normal approximation,- What are the mean and standard deviation of the corresponding normal distribution?
A cup is being drawn from a sheet metal that has a normal anisotropy of 3. Estimate the maximum ratio of cup height to cup diameter that can be drawn successfully in a single draw. Assume that the thickness of the sheet throughout the cup remains ..
What is the correction for continuity and why is it employed when the normal distribution is used in approximating the binomial distribution?
When Edgar finally gets back to the city, what is the probability that he will have an exciting story to tell about how his flashlight and its SuperVolt battery were two of the heroes in his rescue?
这门课三take-a-ways y是什么ou could use to implement this trend? Given the financial alignment models in the health care industry today, would this technology be readily accepted and cost justified?
If we assume a normal distribution and a standard deviation of σ = $0.20. , what proportion of passenger trips produced a revenue of less than $1.05?
Explain your recommended steps in the systematic evaluation and acquisition of the technology. Develop a Project Charter for how you would plan for implementing this technology.
A steel bar of length 30 inches and circular cross section whose diameter varies linearly from 0.50 inches at one end to 0.75 inches at the other is subjected to an axial tensile force of 4.5 kip. Find the change in length of the bar.
What is the settling velocity of a floc of diameter 0.15 mm and density 2.12 g/cm3 in water? 2- Will the floc from problem 4 be completely removed in a typical sedimentation basin if alum was used as the coagulant?
The three hinged arch is composed of segments of a circle. Support points A and D are not at the same level. Determine (a) the horizontal and vertical components of reaction at A and D. (b) the shear, thrust, and moment in the arch at point C.
An earthen channel will be excavated into sandy soil for which Vmax = 4.0 ft/sec, n = 0.022, and the recommended m = 3. The channel will have a bottom slope of 0.0011 and accommodate a design flow of 303 cfs. Design (size) the channel section.
An undisturbed soil sample was collected in a sampling tube of internal diameter 5cm. The length of the extracted sample was 10.2 cm and its mass was 360 g. After oven drying the mass reduced to 326.5 g.
A soil sample is obtained by pushing a 16 inch long tube into the side of a pit. The tube has an inside diameter of 3 inch and weighs 1.8 lb. The soil in the tube is trimmed so that its ends are flush with the ends of the tube.
I want to use PESTAN model for a project, can you please tell me any real scenario with available data on which I can formulate a project preferably related to oklahoma.
Use these results to determine the maximum normal stress in the material.
鳍d the steel area required for beam which has b = 10 in. and d = 17.5 in. to carry a factored load moment of 1,600 in-kips.
The phase diagram of a typical simple substance contains three phases , liquid vapor and solid separated by boundaries . The critical point terminates the liquid-vapor transition, in water it is at Pc=220.9 bar and Tc=374 degres celcius
When filled to capacity, avertical cylindrical un-pressurized storage tank contains water to a height of 14.5m above its base. Given that the height of the tankis 15m, the diameter 9m and wall thickness 18mm
Assume that the cable between B and the pulley remains vertical and solve for a given value of x.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp:+1-415-670-9521
Phone:+1-415-670-9521
Email:info@expertsmind.com
beplay安卓下载